Z6_EL9QHKG10GPM20IJGE61AK10O0
Z7_P86CH0O0I0RF10IB06HRVQ0087
S2K Commerce - Products Dropdown
Actions
Z7_EL9QHKG10GPM20IJGE61AK10S5
S2K Commerce - Order Entry
Actions
Home
>
Resins, Polyester & Vinylester & Epoxy
> General Purpose Polyester Resin, 1 Gallon Kit with 2 Oz.of MEKP
General Purpose Polyester Resin, 1 Gallon Kit with 2 Oz.of MEKP
Item #:
135232
Manufacturer:
FGCI Website
General Purpose Polyester Resin, 1 Gallon Kit with 2 Oz.of MEKP. Excellent for Laminating with Fiberglass Reinforcements, Fast Wet Out and Low Sag, High Strength, No Sanding Between Layers
108.55
Each
Quantity:
Avoid using product in direct sunlight.
The ideal temperature for use of this product is 77°F. Best results for this product can be obtained at temperatures between 70°F and 85°F, in a clean, dry, dust-free environment.
It is generally not recommended to wet out fiberglass over 1/8 in thickness. Use of more than 1/8 may generate excessive heat. Allow layer to tack up, but not fully cure, prior to adding additional layers.
General Purpose Polyester resin is a standard grade of a formulated product. This unsaturated polyester resin is designed to wet out the glass reinforcement rapidly without drainage. The rapid wetting will save time in laying up laminates.
This is an economical resin, designed for hand lay up of boats, panels and other industrial fabrication of demanding quality.
If sanding is required to apply more fiberglass, use 36, 24 or 16 grit. Low grits will create deeper scratches, allowing the new layer to adhere better to the existing one. Be sure to clean the surface before applying another layer.
To apply gelcoat over the resin, prep the surface with 80 grit sandpaper. To apply primer, prep the surface with 220 grit sandpaper. To apply paint, prep the surface with 320 grit sandpaper.
If you have any additional questions or need a product for critical applications, please contact Customer Service at 1-800-272-7890
Directions for Use:
Step 1: Choose the appropriate volume for your project. The type of fiberglass materials used will determine the amount of resin needed.
Step 2: Make sure to agitate or stir the product thoroughly before use.
Step 3: Mix in 1 to 2% MEKP. Please refer to Catalyst Concentration Chart for quantities.
Step 4: Thinner fiberglass can easily be wet through. To thoroughly wet out heavier materials, apply resin first to one side, then flip the glass over to wet out the other side. Use paint-style rollers to distribute resin quickly.
Step 5: Roll each layer with a glass roller to remove air. The fiberglass will go completely transparent when it is adequately wet.
Step 6: Add sanding aid (Product #123833) to the final coat to allow a full cure and a tack-free surface. Refer to Sanding Aid Chart for quantities.
The ideal temperature for use of this product is 77°F. Best results for this product can be obtained at temperatures between 70°F and 85°F, in a clean, dry, dust-free environment.
It is generally not recommended to wet out fiberglass over 1/8 in thickness. Use of more than 1/8 may generate excessive heat. Allow layer to tack up, but not fully cure, prior to adding additional layers.
General Purpose Polyester resin is a standard grade of a formulated product. This unsaturated polyester resin is designed to wet out the glass reinforcement rapidly without drainage. The rapid wetting will save time in laying up laminates.
This is an economical resin, designed for hand lay up of boats, panels and other industrial fabrication of demanding quality.
If sanding is required to apply more fiberglass, use 36, 24 or 16 grit. Low grits will create deeper scratches, allowing the new layer to adhere better to the existing one. Be sure to clean the surface before applying another layer.
To apply gelcoat over the resin, prep the surface with 80 grit sandpaper. To apply primer, prep the surface with 220 grit sandpaper. To apply paint, prep the surface with 320 grit sandpaper.
If you have any additional questions or need a product for critical applications, please contact Customer Service at 1-800-272-7890
Directions for Use:
Step 1: Choose the appropriate volume for your project. The type of fiberglass materials used will determine the amount of resin needed.
Step 2: Make sure to agitate or stir the product thoroughly before use.
Step 3: Mix in 1 to 2% MEKP. Please refer to Catalyst Concentration Chart for quantities.
Step 4: Thinner fiberglass can easily be wet through. To thoroughly wet out heavier materials, apply resin first to one side, then flip the glass over to wet out the other side. Use paint-style rollers to distribute resin quickly.
Step 5: Roll each layer with a glass roller to remove air. The fiberglass will go completely transparent when it is adequately wet.
Step 6: Add sanding aid (Product #123833) to the final coat to allow a full cure and a tack-free surface. Refer to Sanding Aid Chart for quantities.
Resins, Polyester & Vinylester & Epoxy
Size
gallon
Brand
Polyester
Ground Shipping Only
Clear Catalyst Norox MEKP-925, 2 oz. Used as an activator for gelcoat and polyester resins. (No haz ship fee)
Item#:
132662
Manufacturer:
FGCI Website