Z6_EL9QHKG10GPM20IJGE61AK10O0
Z7_P86CH0O0I0RF10IB06HRVQ0087
S2K Commerce - Products Dropdown
Actions
Z7_EL9QHKG10GPM20IJGE61AK10S5
S2K Commerce - Order Entry
Actions
Your Price:
109.19
Each
Your Price:
55.81
Each
Your Price:
100.78
Each
Your Price:
37.82
Each
Avoid using this product in direct sunlight.
The ideal temperature for use of this product is 77°F. Best results for this product can be obtained at temperatures between 70°F and 85°F, in a clean, dry, dust-free environment.
It is not recommended to wet out fiberglass over 1/8 in thickness. Use of more than 1/8 may generate excessive heat. Allow layer to tack up (but not fully cure) prior to pouring next layer.
Boatyard Polyester Resin is a non-specified resin that contains different types of polyester resins and wax. Material may cure hard and tack-free due to wax. If so, product will need to be sanded prior to adding another layer in order to promote good bonding.
This is an economical laminating resin for repairs on boats, small parts production, autos, etc. Not recommended for use below the waterline.
If sanding is required to apply more fiberglass, use 36, 24, or 16 grit. Low grits will create deeper scratches to make the new layer adhere better to the existing one. Be sure to clean the surface before applying another layer.
To apply gelcoat, prep the surface with 80 grit sandpaper. To apply primer, prep the surface with 220 grit sandpaper. To apply paint, prep the surface with 320 grit sandpaper.
If you have any additional questions or need a product for critical applications, please contact Customer Service at 1-800-272-7890
Directions for Use:
Step 1: Choose the appropriate volume for your project. The type of fiberglass used will determine the amount of resin needed.
Step 2: Make sure to agitate or stir the product thoroughly before use.
Step 3: Mix 1 to 2% MEKP, in resin solution thoroughly. Please refer to Catalyst Concentration Chart for quantities.
Step 4: Thinner fiberglass can easily be wet through. To thoroughly wet out heavier materials, apply resin first to one side, then flip the glass over to wet out the other side. Use paint-style rollers to distribute resin quickly.
Step 5: Roll each layer with a glass roller to remove air. The fiberglass will go completely transparent when it is adequately wet.
Step 6: Add sanding aid (Product #123833) to the final coat to allow a full cure and a tack-free surface. Refer to Sanding Aid Chart for quantities.
The ideal temperature for use of this product is 77°F. Best results for this product can be obtained at temperatures between 70°F and 85°F, in a clean, dry, dust-free environment.
It is not recommended to wet out fiberglass over 1/8 in thickness. Use of more than 1/8 may generate excessive heat. Allow layer to tack up (but not fully cure) prior to pouring next layer.
Boatyard Polyester Resin is a non-specified resin that contains different types of polyester resins and wax. Material may cure hard and tack-free due to wax. If so, product will need to be sanded prior to adding another layer in order to promote good bonding.
This is an economical laminating resin for repairs on boats, small parts production, autos, etc. Not recommended for use below the waterline.
If sanding is required to apply more fiberglass, use 36, 24, or 16 grit. Low grits will create deeper scratches to make the new layer adhere better to the existing one. Be sure to clean the surface before applying another layer.
To apply gelcoat, prep the surface with 80 grit sandpaper. To apply primer, prep the surface with 220 grit sandpaper. To apply paint, prep the surface with 320 grit sandpaper.
If you have any additional questions or need a product for critical applications, please contact Customer Service at 1-800-272-7890
Directions for Use:
Step 1: Choose the appropriate volume for your project. The type of fiberglass used will determine the amount of resin needed.
Step 2: Make sure to agitate or stir the product thoroughly before use.
Step 3: Mix 1 to 2% MEKP, in resin solution thoroughly. Please refer to Catalyst Concentration Chart for quantities.
Step 4: Thinner fiberglass can easily be wet through. To thoroughly wet out heavier materials, apply resin first to one side, then flip the glass over to wet out the other side. Use paint-style rollers to distribute resin quickly.
Step 5: Roll each layer with a glass roller to remove air. The fiberglass will go completely transparent when it is adequately wet.
Step 6: Add sanding aid (Product #123833) to the final coat to allow a full cure and a tack-free surface. Refer to Sanding Aid Chart for quantities.
Your Price:
77.99
Each
Avoid using product in direct sunlight.
The ideal temperature for use of this product is 77°F. Best results for this product can be obtained at temperatures between 70°F and 85°F, in a clean, dry, dust-free environment.
It is generally not recommended to wet out fiberglass over 1/8 in thickness. Use of more than 1/8 may generate excessive heat. Allow layer to tack up, but not fully cure, prior to adding additional layers.
General Purpose Polyester resin is a standard grade of a formulated product. This unsaturated polyester resin is designed to wet out the glass reinforcement rapidly without drainage. The rapid wetting will save time in laying up laminates.
This is an economical resin, designed for hand lay up of boats, panels and other industrial fabrication of demanding quality.
If sanding is required to apply more fiberglass, use 36, 24 or 16 grit. Low grits will create deeper scratches, allowing the new layer to adhere better to the existing one. Be sure to clean the surface before applying another layer.
To apply gelcoat over the resin, prep the surface with 80 grit sandpaper. To apply primer, prep the surface with 220 grit sandpaper. To apply paint, prep the surface with 320 grit sandpaper.
If you have any additional questions or need a product for critical applications, please contact Customer Service at 1-800-272-7890
Directions for Use:
Step 1: Choose the appropriate volume for your project. The type of fiberglass materials used will determine the amount of resin needed.
Step 2: Make sure to agitate or stir the product thoroughly before use.
Step 3: Mix in 1 to 2% MEKP. Please refer to Catalyst Concentration Chart for quantities.
Step 4: Thinner fiberglass can easily be wet through. To thoroughly wet out heavier materials, apply resin first to one side, then flip the glass over to wet out the other side. Use paint-style rollers to distribute resin quickly.
Step 5: Roll each layer with a glass roller to remove air. The fiberglass will go completely transparent when it is adequately wet.
Step 6: Add sanding aid (Product #123833) to the final coat to allow a full cure and a tack-free surface. Refer to Sanding Aid Chart for quantities.
The ideal temperature for use of this product is 77°F. Best results for this product can be obtained at temperatures between 70°F and 85°F, in a clean, dry, dust-free environment.
It is generally not recommended to wet out fiberglass over 1/8 in thickness. Use of more than 1/8 may generate excessive heat. Allow layer to tack up, but not fully cure, prior to adding additional layers.
General Purpose Polyester resin is a standard grade of a formulated product. This unsaturated polyester resin is designed to wet out the glass reinforcement rapidly without drainage. The rapid wetting will save time in laying up laminates.
This is an economical resin, designed for hand lay up of boats, panels and other industrial fabrication of demanding quality.
If sanding is required to apply more fiberglass, use 36, 24 or 16 grit. Low grits will create deeper scratches, allowing the new layer to adhere better to the existing one. Be sure to clean the surface before applying another layer.
To apply gelcoat over the resin, prep the surface with 80 grit sandpaper. To apply primer, prep the surface with 220 grit sandpaper. To apply paint, prep the surface with 320 grit sandpaper.
If you have any additional questions or need a product for critical applications, please contact Customer Service at 1-800-272-7890
Directions for Use:
Step 1: Choose the appropriate volume for your project. The type of fiberglass materials used will determine the amount of resin needed.
Step 2: Make sure to agitate or stir the product thoroughly before use.
Step 3: Mix in 1 to 2% MEKP. Please refer to Catalyst Concentration Chart for quantities.
Step 4: Thinner fiberglass can easily be wet through. To thoroughly wet out heavier materials, apply resin first to one side, then flip the glass over to wet out the other side. Use paint-style rollers to distribute resin quickly.
Step 5: Roll each layer with a glass roller to remove air. The fiberglass will go completely transparent when it is adequately wet.
Step 6: Add sanding aid (Product #123833) to the final coat to allow a full cure and a tack-free surface. Refer to Sanding Aid Chart for quantities.
Your Price:
108.55
Each
Avoid using product in direct sunlight.
The ideal temperature for use of this product is 77°F. Best results for this product can be obtained at temperatures between 70°F and 85°F, in a clean, dry, dust-free environment.
It is generally not recommended to wet out fiberglass over 1/8 in thickness. Use of more than 1/8 may generate excessive heat. Allow layer to tack up, but not fully cure, prior to adding additional layers.
General Purpose Polyester resin is a standard grade of a formulated product. This unsaturated polyester resin is designed to wet out the glass reinforcement rapidly without drainage. The rapid wetting will save time in laying up laminates.
This is an economical resin, designed for hand lay up of boats, panels and other industrial fabrication of demanding quality.
If sanding is required to apply more fiberglass, use 36, 24 or 16 grit. Low grits will create deeper scratches, allowing the new layer to adhere better to the existing one. Be sure to clean the surface before applying another layer.
To apply gelcoat over the resin, prep the surface with 80 grit sandpaper. To apply primer, prep the surface with 220 grit sandpaper. To apply paint, prep the surface with 320 grit sandpaper.
If you have any additional questions or need a product for critical applications, please contact Customer Service at 1-800-272-7890
Directions for Use:
Step 1: Choose the appropriate volume for your project. The type of fiberglass materials used will determine the amount of resin needed.
Step 2: Make sure to agitate or stir the product thoroughly before use.
Step 3: Mix in 1 to 2% MEKP. Please refer to Catalyst Concentration Chart for quantities.
Step 4: Thinner fiberglass can easily be wet through. To thoroughly wet out heavier materials, apply resin first to one side, then flip the glass over to wet out the other side. Use paint-style rollers to distribute resin quickly.
Step 5: Roll each layer with a glass roller to remove air. The fiberglass will go completely transparent when it is adequately wet.
Step 6: Add sanding aid (Product #123833) to the final coat to allow a full cure and a tack-free surface. Refer to Sanding Aid Chart for quantities.
The ideal temperature for use of this product is 77°F. Best results for this product can be obtained at temperatures between 70°F and 85°F, in a clean, dry, dust-free environment.
It is generally not recommended to wet out fiberglass over 1/8 in thickness. Use of more than 1/8 may generate excessive heat. Allow layer to tack up, but not fully cure, prior to adding additional layers.
General Purpose Polyester resin is a standard grade of a formulated product. This unsaturated polyester resin is designed to wet out the glass reinforcement rapidly without drainage. The rapid wetting will save time in laying up laminates.
This is an economical resin, designed for hand lay up of boats, panels and other industrial fabrication of demanding quality.
If sanding is required to apply more fiberglass, use 36, 24 or 16 grit. Low grits will create deeper scratches, allowing the new layer to adhere better to the existing one. Be sure to clean the surface before applying another layer.
To apply gelcoat over the resin, prep the surface with 80 grit sandpaper. To apply primer, prep the surface with 220 grit sandpaper. To apply paint, prep the surface with 320 grit sandpaper.
If you have any additional questions or need a product for critical applications, please contact Customer Service at 1-800-272-7890
Directions for Use:
Step 1: Choose the appropriate volume for your project. The type of fiberglass materials used will determine the amount of resin needed.
Step 2: Make sure to agitate or stir the product thoroughly before use.
Step 3: Mix in 1 to 2% MEKP. Please refer to Catalyst Concentration Chart for quantities.
Step 4: Thinner fiberglass can easily be wet through. To thoroughly wet out heavier materials, apply resin first to one side, then flip the glass over to wet out the other side. Use paint-style rollers to distribute resin quickly.
Step 5: Roll each layer with a glass roller to remove air. The fiberglass will go completely transparent when it is adequately wet.
Step 6: Add sanding aid (Product #123833) to the final coat to allow a full cure and a tack-free surface. Refer to Sanding Aid Chart for quantities.
Your Price:
2.93
Pound
Item#:
141816
Ground Shipping Only
Heavy
Oversized Shipping
Your Price:
2.71
POUND
Directions for Use:
Step 1: Choose the appropriate volume for your project. The type of fiberglass used will determine the amount of resin needed.
Step 2: Make sure to agitate or stir the product thoroughly before use.
Step 3: Mix in the MEKP, stirring thoroughly. Please refer to the Catalyst Concentration Chart for quantities.
Step 4: Thinner fiberglass can easily be wet through. To thoroughly wet out heavier materials, apply resin first to one side, then flip the glass over to wet out the other side. Use paint-style rollers to distribute resin quickly.
Step 5: Roll each layer with a glass roller to remove air. The fiberglass will go completely transparent when it is adequately wet.
Step 6: Add sanding aid (Product #123833) to the final coat to allow a full cure and a tack-free surface.
This item is temporarily unavailable.
Directions for Use:
Step 1: The ideal working temperature is around 77°F. Best results can be obtained at temperatures between 70°F and 85°F, in a clean, dry, dust-free environment. Avoid working in high humidity. We recommend using this product on a leveled and flat work surface.
Step 2: Using the Laminate Coverage Chart, measure product in accordance with your intended use. Prepare 1 part Base Resin to 1 part Curing Agent by liquid volume or 100 parts Base Resin to 83 parts Curing Agent by weight. Pour the Curing Agent first and then the Base Resin into a clean, smooth-sided container large enough to hold all the liquid and allow room for mixing.
Step 3: The material must be mixed thoroughly for at least 3 minutes. Be sure to scrape the container sides, bottom, and corners as you mix. Be careful to not whip excessive air into the mixture. If mixing a gallon, use a power mixer set to hand speed. For smaller quantities, use stir sticks. Do not mix more than a gallon.
Step 4: Pour the mixed resin onto the surface and distribute evenly with a squeegee or gloved hand. Continue to pour remaining material to achieve the desired thickness, allowing the resin to flow evenly over the projects sides.
Step 5: See Additional Information for guidance to help eliminate bubbles that have risen to the surface of the resin.
Step 6: If you are going to make a second pour, the first pour should still be lightly sticky. Once the second pour is made, bubbles may once again need to be removed. Material will feel well-cured after 24 hours, but full cure and maximum hardness can require up to 7 days depending upon the temperature.
Step 1: The ideal working temperature is around 77°F. Best results can be obtained at temperatures between 70°F and 85°F, in a clean, dry, dust-free environment. Avoid working in high humidity. We recommend using this product on a leveled and flat work surface.
Step 2: Using the Laminate Coverage Chart, measure product in accordance with your intended use. Prepare 1 part Base Resin to 1 part Curing Agent by liquid volume or 100 parts Base Resin to 83 parts Curing Agent by weight. Pour the Curing Agent first and then the Base Resin into a clean, smooth-sided container large enough to hold all the liquid and allow room for mixing.
Step 3: The material must be mixed thoroughly for at least 3 minutes. Be sure to scrape the container sides, bottom, and corners as you mix. Be careful to not whip excessive air into the mixture. If mixing a gallon, use a power mixer set to hand speed. For smaller quantities, use stir sticks. Do not mix more than a gallon.
Step 4: Pour the mixed resin onto the surface and distribute evenly with a squeegee or gloved hand. Continue to pour remaining material to achieve the desired thickness, allowing the resin to flow evenly over the projects sides.
Step 5: See Additional Information for guidance to help eliminate bubbles that have risen to the surface of the resin.
Step 6: If you are going to make a second pour, the first pour should still be lightly sticky. Once the second pour is made, bubbles may once again need to be removed. Material will feel well-cured after 24 hours, but full cure and maximum hardness can require up to 7 days depending upon the temperature.
Your Price:
116.52
Each
Avoid using product in direct sunlight.
The ideal temperature for use of this product is 77°F. Best results for this product can be obtained at temperatures between 70°F and 85°F, in a clean, dry, dust-free environment.
It is generally not recommended to wet out fiberglass over 1/8 in thickness. Use of more than 1/8 may generate excessive heat. Allow layer to tack up, but not fully cure, prior to adding additional layers.
General Purpose Polyester resin is a standard grade of a formulated product. This unsaturated polyester resin is designed to wet out the glass reinforcement rapidly without drainage. The rapid wetting will save time in laying up laminates.
This is an economical resin, designed for hand lay up of boats, panels and other industrial fabrication of demanding quality.
If sanding is required to apply more fiberglass, use 36, 24 or 16 grit. Low grits will create deeper scratches, allowing the new layer to adhere better to the existing one. Be sure to clean the surface before applying another layer.
To apply gelcoat over the resin, prep the surface with 80 grit sandpaper. To apply primer, prep the surface with 220 grit sandpaper. To apply paint, prep the surface with 320 grit sandpaper.
If you have any additional questions or need a product for critical applications, please contact Customer Service at 1-800-272-7890
Directions for Use:
Step 1: Choose the appropriate volume for your project. The type of fiberglass materials used will determine the amount of resin needed.
Step 2: Make sure to agitate or stir the product thoroughly before use.
Step 3: Mix in 1 to 2% MEKP. Please refer to Catalyst Concentration Chart for quantities.
Step 4: Thinner fiberglass can easily be wet through. To thoroughly wet out heavier materials, apply resin first to one side, then flip the glass over to wet out the other side. Use paint-style rollers to distribute resin quickly.
Step 5: Roll each layer with a glass roller to remove air. The fiberglass will go completely transparent when it is adequately wet.
Step 6: Add sanding aid (Product #123833) to the final coat to allow a full cure and a tack-free surface. Refer to Sanding Aid Chart for quantities.
The ideal temperature for use of this product is 77°F. Best results for this product can be obtained at temperatures between 70°F and 85°F, in a clean, dry, dust-free environment.
It is generally not recommended to wet out fiberglass over 1/8 in thickness. Use of more than 1/8 may generate excessive heat. Allow layer to tack up, but not fully cure, prior to adding additional layers.
General Purpose Polyester resin is a standard grade of a formulated product. This unsaturated polyester resin is designed to wet out the glass reinforcement rapidly without drainage. The rapid wetting will save time in laying up laminates.
This is an economical resin, designed for hand lay up of boats, panels and other industrial fabrication of demanding quality.
If sanding is required to apply more fiberglass, use 36, 24 or 16 grit. Low grits will create deeper scratches, allowing the new layer to adhere better to the existing one. Be sure to clean the surface before applying another layer.
To apply gelcoat over the resin, prep the surface with 80 grit sandpaper. To apply primer, prep the surface with 220 grit sandpaper. To apply paint, prep the surface with 320 grit sandpaper.
If you have any additional questions or need a product for critical applications, please contact Customer Service at 1-800-272-7890
Directions for Use:
Step 1: Choose the appropriate volume for your project. The type of fiberglass materials used will determine the amount of resin needed.
Step 2: Make sure to agitate or stir the product thoroughly before use.
Step 3: Mix in 1 to 2% MEKP. Please refer to Catalyst Concentration Chart for quantities.
Step 4: Thinner fiberglass can easily be wet through. To thoroughly wet out heavier materials, apply resin first to one side, then flip the glass over to wet out the other side. Use paint-style rollers to distribute resin quickly.
Step 5: Roll each layer with a glass roller to remove air. The fiberglass will go completely transparent when it is adequately wet.
Step 6: Add sanding aid (Product #123833) to the final coat to allow a full cure and a tack-free surface. Refer to Sanding Aid Chart for quantities.
This item is temporarily unavailable.
FGCI Superbond Epoxy Adhesive is a two-component, 100% solid system designed for adhesive bonding and the fitting and fairing of a wide variety of substrates.
The material features a highly thixotropic, paste-like consistency, which hangs well in thick sections on vertical and overhead surfaces.
The material cures to a hard, blush-free, amber- colored, high-strength, moisture-resistant plastic with excellent adhesive properties.
Additional recoating of this material should be done before the material is thoroughly cured.
If the material has cured hard and tack-free, a light sanding and solvent wash is advisable before recoating.
Epoxy cures faster at higher temperatures and in thicker layered applications.
Directions for Use:
Step 1: Required prep will vary according to application surface:
Ceramics, Composites, Plastics & Wood Must be oil free and sanded 80 grit or rougher.
Glass Must be sanded with 220 grit or lower until shine is removed.
Metals All metals must be carefully degreased with trisodium phosphate (TSP). Depending on the type of metal, prep work may vary.
Step 2: Be sure to clean the application site, removing all dust and debris.
Step 3: FGCIs Superbond Base Resin may be used with any of the three Activators, which differ in curing time:
Standard Activator
Medium Activator
Fast Activator
Please refer to Properties Chart for gel time.
Step 4: Mix at a 1:1 ratio by volume or weight, equal parts Base and Activator.
Step 5: Stir thoroughly, being sure to scrape sides and bottom of container. For best results, do not mix more than a quart at a time.
The material features a highly thixotropic, paste-like consistency, which hangs well in thick sections on vertical and overhead surfaces.
The material cures to a hard, blush-free, amber- colored, high-strength, moisture-resistant plastic with excellent adhesive properties.
Additional recoating of this material should be done before the material is thoroughly cured.
If the material has cured hard and tack-free, a light sanding and solvent wash is advisable before recoating.
Epoxy cures faster at higher temperatures and in thicker layered applications.
Directions for Use:
Step 1: Required prep will vary according to application surface:
Ceramics, Composites, Plastics & Wood Must be oil free and sanded 80 grit or rougher.
Glass Must be sanded with 220 grit or lower until shine is removed.
Metals All metals must be carefully degreased with trisodium phosphate (TSP). Depending on the type of metal, prep work may vary.
Step 2: Be sure to clean the application site, removing all dust and debris.
Step 3: FGCIs Superbond Base Resin may be used with any of the three Activators, which differ in curing time:
Standard Activator
Medium Activator
Fast Activator
Please refer to Properties Chart for gel time.
Step 4: Mix at a 1:1 ratio by volume or weight, equal parts Base and Activator.
Step 5: Stir thoroughly, being sure to scrape sides and bottom of container. For best results, do not mix more than a quart at a time.
Item#:
125323
Your Price:
30.12
Each